All products

ImageNameSummaryPriceBuy
2-stroke engines

RVS TECHNOLOGY® for 2-stroke petrol engines

Easily increase the economy, durability and environmental friendliness of your vehicle. RVS TECHNOLOGY® is proven to protect surfaces and equipment from wear. By reducing friction, the amount of energy wasted is reduced. This leads to lower emissions and more efficient engine operation. The engine becomes long-lasting and economically efficient.

The treatment is easy to do yourself:

1. RVS Technology® 2-Stroke Engine Treatment is recommended to start with an almost empty fuel tank.

2. Shake thoroughly (20-30 sec) until the mixture is homogeneous. No residue should remain at the bottom of the bottle. The bottle contains 90 ml of a mixture of synthetic 2-stroke oil and RVS Technology®.

3. 2-stroke engines are treated by adding the contents of the bottle either to the petrol or to the fresh lubrication system

– 1 bottle of RVS Technology® 2-Stroke Engine Treatment 125cc to 10 litres of petrol.

– 1 bottle of RVS Technology® 2-Stroke Engine Treatment 500cc to 15 litres of petrol.

4. Pour the prepared mixture into a fuel tank, or preferably into a nearly empty fresh lubrication tank.

5. Run the engine as it is normally intended for use, without interruption, for 1-2 hours – initially at lower revs without overloading the engine.

23,9069,90
For gasoline (petrol) engines

RVS TECHNOLOGY® for 4-stroke gasoline (petrol) engines

Improve the economy and durability of your vehicle while you make it environmentally more friendly. RVS TECHNOLOGY® is certified to protect surfaces abd mechanisms from wear. As the friction reduces, the energy loss is reduced. This leads to reduced emissions and improves engine operation. The engine becomes long-lasting and economically effective.

The treatment is easy to carry out by yourself:

  1. Let the engine idle or operate for at least 5 minutes unless it is already warm.
  2. Mix the product contents of the package. Shake well.
  3. Shut the engine down, open the hood (bonnet), and and pour one half of the mixture into the engine via the oil filling hole.
  4. Let the engine idle for about 15 minutes. Stop the engine and pour the rest of the mixture into the oil filling hole.
  5. Start the engine and drive for at least 30 to 40 minutes.

You guarantee the best possible result by renewing the treatment about 400 km (250 miles) after the first treatment. It is recommended to carry out the second treatment after oil change. A second treatment is recommended for vehicles with a mileage of over 40,000 km (25,000 miles).

28,90199,80
For Diesel­ engines

RVS TECHNOLOGY® for four-stroke diesel engines

Improve the economy and durability of your vehicle while you make it environmentally more friendly. RVS TECHNOLOGY® protects surfaces and equipment from wear. As the friction reduces, the energy loss is reduced. This leads to reduced emissions and improves engine operation. The engine becomes long-lasting and economically effective.

The treatment is easy to carry out by yourself:

  1. Let the engine idle or operate for at least 5 minutes unless it is already warm.
  2. Mix the product contents of the package. Shake well.
  3. Shut the engine down, open the hood (bonnet), and and pour one half of the mixture into the engine via the oil filling hole.
  4. Let the engine idle for about 15 minutes. Stop the engine and pour the rest of the mixture into the oil filling hole.
  5. Start the engine and drive for at least 30 to 40 minutes.

You ensure the best possible result by renewing the treatment about 400 km (250 miles) after the first treatment. It is recommended to carry out the second treatment after oil change. The second treatment is recommended for vehicles with a mileage of over 40,000 kms (25,000 miles).

68,90409,90
For manual transmissions

RVS TECHNOLOGY® for transmissions

Improve the economy and durability of your vehicle while you make it environmentally more friendly.
RVS TECHNOLOGY® protects surfaces and equipment from wear. Transmission parts wear, which causes them to become stiff and noisy. After the treatment, the transmission becomes easier to use and it works more accurately.

In the product family, there are products for both automatic and manual transmissions. Carrying out the treatment is easiest if done during a regular service. You can also do it yourself if you know where to add oil to the transmission.

46,9069,90
For marine transmissions GL5, 80W-90

RVS TECHNOLOGY® for marine transmissions, which use differential oil (GL-5, 80W-90)

Improve the economy, durability and ecology of your boat very easily. RVS TECHNOLOGY® protects surfaces and equipment from wear. Marine Gear Oil is an efficient high quality oil specifically developed for inboard and outboard engine transmissions, suitable also for Z and L couplings. Transmission parts wear very easily, and it causes the transmission to become stiff and noisy. The treatment reduces friction and, as a consequence, wear, noise, and vibrations. The Marine Gear Oil is available in two sizes.

For other transmission types, we recommend RVS Technology transmission (T series) products.

All RVS products intended for vehicles can also be used for treating corresponding marine equipment. Carry out the treatment procedures in accordance with the instructions enclosed in the packages.

18,9049,90
Front axle differentials

RVS TECHNOLOGY® for transmissions

Improve the economy and durability of your vehicle while you make it environmentally more friendly.
RVS TECHNOLOGY® protects surfaces and equipment from wear. Transmission parts wear, which causes them to become stiff and noisy. After the treatment, the transmission becomes easier to use and it works more accurately.

In the product family, there are products for both automatic and manual transmissions. Carrying out the treatment is easiest if done during a regular service. You can also do it yourself if you know where to add oil to the transmission.

46,9069,90
Diesel engines and hydraulic systems

RVS Technology Engine & Hydraulics Protection & Restoration

RVS Technology Engine & Hydraulics Protection & Restoration is a product for the treatment of systems on tractors and other machinery with combined diesel engine and hydraulic system oil circulation.

Unlike when dealing with internal combustion engines alone, when dealing with hydraulic systems, the amount of oil is not an important consideration – the hydraulics may have a lot of oil filling in the working cylinders, but there may be only small amounts of friction surfaces to be treated. In hydraulics, the RVS product only affects mainly the pump and valves, while hydraulic cylinders and pistons are usually minimally or not at all impacted.

329,90
Dieselengines ja hydraulic systems

RVS Technology Engine & Hydraulics Protection & Restoration

RVS Technology Engine & Hydraulics Protection & Restoration is a product for the treatment of systems on tractors and other machinery with combined diesel engine and hydraulic system oil circulation.

Unlike when dealing with internal combustion engines alone, when dealing with hydraulic systems, the amount of oil is not an important consideration – the hydraulics may have a lot of oil filling in the working cylinders, but there may be only small amounts of friction surfaces to be treated. In hydraulics, the RVS product only affects mainly the pump and valves, while hydraulic cylinders and pistons are usually minimally or not at all impacted.

329,90
For automatic transmissions

RVS TECHNOLOGY® for transmissions

Improve the economy and durability of your vehicle while you make it environmentally more friendly.
RVS TECHNOLOGY® protects surfaces and equipment from wear. Transmission parts wear, which causes them to become stiff and noisy. After the treatment, the transmission becomes easier to use and it works more accurately.

In the product family, there are products for both automatic and manual transmissions. Carrying out the treatment is easiest if done during a regular service. You can also do it yourself if you know where to add oil to the transmission.

82,90113,90
For fuel injection systems of gasoline (petrol) engines

RVS TECHNOLOGY® for fuel injection systems

Improve the economy and durability of your vehicle while you make it environmentally more friendly. RVS TECHNOLOGY® protects surfaces and equipment from wear. By treating your fuel system, you clean, restore, and protect the fuel pump and injectors of your vehicle. It improves the combustion process and prevents fuel pump failures.

The treatment is easy to carry out by yourself:

It is recommended to start the RVS Technology® Injection System Protection & Restoration procedures when the fuel tank is almost empty (the amount of fuel is sufficient for 45-to-60-minute driving). The fuel temperature has to be min. +10 °C (50 °F).
Shake the bottle well (20–30 sec.) until the mixture is homogenous.
Pour the contents of the bottle into the fuel tank.
Let the engine operate – preferably in driving conditions – until the fuel tank is almost empty. Avoid stopping the engine during this time. Fill up the fuel tank and continue using the vehicle as usual.
The treatment is complete after approximately 300 to 500 km (180 to 300 miles) of driving.

You guarantee the best possible result if you treat the engine with RVS Technology® Engine Protection & Restoration products first.

46,90
Transmissions and Hydraulics

RVS Technology Transmissions & Hydraulics Protection & Restoration

RVS Technology Transmissions & Hydraulics Protection & Restoration is a product for the treatment of systems on tractors and other machinery with combined hydraulic system oil circulation in transmissions or final drives.

Unlike when dealing with transmissions alone, when dealing with hydraulic systems, the amount of oil is not the important information – the hydraulics may have a lot of oil filling inside the working cylinders, but there may be only a limited number of surfaces to be treated. In hydraulics, the RVS product only affects mainly the pump and valves, while hydraulic cylinders and pistons are usually minimally or not at all impacted.

 

244,90
Rear axle differentials

RVS TECHNOLOGY® for transmissions

Improve the economy and durability of your vehicle while you make it environmentally more friendly.
RVS TECHNOLOGY® protects surfaces and equipment from wear. Transmission parts wear, which causes them to become stiff and noisy. After the treatment, the transmission becomes easier to use and it works more accurately.

In the product family, there are products for both automatic and manual transmissions. Carrying out the treatment is easiest if done during a regular service. You can also do it yourself if you know where to add oil to the transmission.

46,9069,90
For diesel injection systems

RVS TECHNOLOGY® for fuel injection systems

Improve the economy and durability of your vehicle while you make it environmentally more friendly. RVS TECHNOLOGY® protects surfaces and equipment from wear. By treating your fuel system, you clean, restore, and protect the fuel pump and injectors of your vehicle. It improves the combustion process and prevents fuel pump failures.

The treatment is easy to carry out by yourself:

  1. It is recommended to start the RVS Technology® Injection System Protection & Restoration procedures when the fuel tank is almost empty (the amount of fuel is sufficient for 45-to-60-minute driving).
  2. Shake the bottle well (20–30 sec.) until the mixture is homogenous.
  3. Pour the contents of the bottle into the fuel tank.
  4. Let the engine operate – preferably in driving conditions – until the fuel tank is almost empty. Avoid stopping the engine during this time. Fill up the fuel tank and continue using the vehicle as usual.
  5. The treatment is complete after approximately 300 to 500 km (180 to 300 miles) of driving.

You guarantee the best possible result if you treat the engine with RVS Technology® Engine Protection & Restoration products first.

46,90
For power steering

RVS TECHNOLOGY® for hydraulic power steering

Improve the usability of your vehicle very easily. RVS TECHNOLOGY® protects surfaces and equipment from wear. If the steering feels stiff or makes noise, you can improve its operation yourself.

Introduce the RVS Power Steering Protection & Restoration product into the oil reservoir of your power steering system and turn the steering wheel from one extreme position to the other. After the treatment, the steering becomes light, accurate, and noiseless.

The product suits power steering systems with oil capacity up to 2 litres (2 qt.). Attention! Not suitable for electric power steering.

Note that the product affects only the power steering unit. If the steering has other problems, the product has no effect on them. Using the product is not badly spent money in any case as the pump becomes more durable after the RVS treatment.

30,90
Universal Grease

RVS Technology Universal Grease

Molemmat rasvat ovat NLGI 2 -luokiteltuja, mutta niissä ei ole tavanomaisia EP-lisäaineita (EP = Extreme Pressure). Rasvoja voi tilanteesta riippuen käyttää joko ainoana rasvana tai käsittelyrasvana, jota käytetään vuorotellen kohteessa muuten käytettävän tavanomaisen rasvan kanssa esim. niin, että joka toinen, kolmas tai neljäs kerta lisätään RVS Technology -rasvaa.

RVS Technology -rasvat muokkaavat käsiteltävän kohteen metallipintojen väliselle vierintä- ja liukukitkalle alttiita pintoja ja muodostavat kitkan ja paineen yhteisvaikutuksesta keraamisen (tribokeraamisen) pintarakenteen. Muokatun pinnan kitkaominaisuudet ovat paremmat kuin muokkaamattoman pinnan, mikä ilmenee pidempänä käyttöikänä ja pienempänä energiankulutuksena.

Valitse mineraalirasvapohjainen Universal Grease tai synteettisen rasvan pohjalle valmistettu Synthetic Grease sen mukaan, käytetäänkö kohteessa normaalisti mineraali- vai synteettistä rasvaa.

Tuotteita myydään 420 ml:n putkiloissa. Suurasiakkaille tarjolla on myös muita pakkauskokoja (ota yhteyttä)

79,00
Synthetic Grease

RVS Technology Synthetic Grease

Both greases are NLGI 2 classified, but without the usual EP (Extreme Pressure) additives. Depending on the situation, the greases can be used either as the sole grease or as a treatment grease, alternating with the conventional grease otherwise used on site, e.g. adding RVS Technology grease every second, third or fourth time.

RVS Technology greases modify the surfaces susceptible to rolling and sliding friction between the metal surfaces of the object to be treated and, through the combined action of friction and pressure, form a ceramic (triboceramic) surface structure. The frictional properties of the machined surface are superior to those of the unmachined surface, resulting in longer service life and lower energy consumption.

Choose between Universal Grease based on mineral grease or Synthetic Grease based on synthetic grease, depending on whether mineral or synthetic grease is normally used.

The products are sold in 420 ml tubes. Other packaging sizes are also available for volume customers (please contact us).

99,00
Professional Gel 31, 200 ml pump bottle

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

989,00
Professional Gel 31, 400 ml pump bottle

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

1929,00
Professional Gel 31, 400 ml cartridge

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

1929,00
Transfer box (T3-T5)

RVS TECHNOLOGY® for transmissions

Improve the economy and durability of your vehicle while you make it environmentally more friendly.
RVS TECHNOLOGY® protects surfaces and equipment from wear. Transmission parts wear, which causes them to become stiff and noisy. After the treatment, the transmission becomes easier to use and it works more accurately.

In the product family, there are products for both automatic and manual transmissions. Carrying out the treatment is easiest if done during a regular service. You can also do it yourself if you know where to add oil to the transmission.

46,9069,90
Professional Gel 32, 200 ml pump bottle

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

1909,00
Professional Gel 32, 400 ml pump bottle

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

3790,00
Professional Gel 32, 400 ml cartridge

RVS Technology Professional Gel

RVS Technology Professional Gel is designed for professional use and the user must have experience in the application of RVS Technology products. The product can be used instead of several RVS products for different applications. The gel is also suitable for large areas for which there is no pre-dosed RVS Technology product set.

We provide instructions for use for the product or develop instructions for use together with the customer if the application is unusual or technically demanding.

RVS Technology Professional Gel is available in two different concentrations, Professional Gel 31 and Professional Gel 32.

There are three types of packaging: a 200 ml pump bottle, a 400 ml pump bottle and a 400 ml cartridge.

For big customers, we also sell products in other types of packaging on request (please contact us).

3790,00

Miksi valita RVS-tuotteet?

RVS-tuotteet ovat täysin omaa luokkaansa verrattuna perinteisiin moottoriöljyihin ja lisäaineisiin. RVS-tuotteiden ei ole tarkoitus korvata niitä vaan auttaa niitä toimimaan siten kuin ne on suunniteltu helpottamalla niiden toimintamahdollisuuksia.

Tuotteemme ovat ihanteellisia kaikille moottoreille, kun tavoitteena on vähentää kulutusta, lisätä tehoa, pidentää huoltovälejä ja parantaa kestävyyttä, tai kun moottori ei kulumisensa vuoksi enää meinaa mennä läpi katsastuksen päästötestistä. Vaihteistoissa RVS-tuotteilla voidaan pienentää tehohävikkiä ja parantaa sen toimintaa. Kaikissa tapauksissa laitteen kuluminen vähenee ja alkanutta kuluneisuutta voidaan korjata keraamilla.

RVS ei vaikuta moottoriöljyyn millään lailla, minkä ansiosta käsittely on huomattavasti pitkäaikaisempi kuin öljynvaihtoväli. RVS-tuotteiden teho perustuu tribokeraamiseen käsittelyyn, jossa tietyt RVS-yhdisteen ainesosat reagoivat laitteen metallipintojen kanssa ja tuottavat ohuen, mutta kestävän suojakerroksen. Keraamin muodostumisen sivuvaikutuksena on myös käytön aikana kertyneiden epäpuhtauksien irtoaminen niistä kohdista, joissa RVS-aine reagoi metallin pinnan kanssa.

Moottorivalmistajat ovat jo pitkään halunneet tehdä keraamista moottoria siinä onnistumatta. RVS-tuotteilla moottorin keraamisen pintarakenteen hyödyt on mahdollista saavuttaa helposti, nopeasti ja kustannustehokkaasti niin uudessa kuin vanhassakin moottorissa.

Lue lisää: Mitä on RVS?